Microsonic pico+15/I Instrukcja Użytkownika Pobierz pdf

Operating Instructions

pico+15/I pico+15/WK/I

pico+25/I pico+25/WK/I

pico+35/I pico+35/WK/I

pico+100/I pico+100/WK/I

pico+15/U pico+15/WK/U

pico+25/U pico+25/WK/U

pico+35/U pico+35/WK/U

pico+100/U pico+100/WK/U

Ultrasonic sensor with one ana-

logue output

Product Description

The pico+sensor offers a non-contact

measurement of the distance to an

object that has to be present within

the sensor’s detection zone. Depend-

ing on the set window limits, a dis-

tance-proportional analogue signal is

output.

The window limits of the analogue

output and its characteristic can be

adjusted with the Teach-in proce-

dure.

Two LEDs indicate operation and the

state of the analogue output.

Safety Notes

 Read the operating instructions

prior to start-up.

Sensor adjustment with Teach-in procedure

Set window

margins

Place object at position 

Connect Com for about

3 s to +U

, until both LEDs

flash simultaneously

Both LEDs:

Place object at position 

flash alternately

Set rising/falling output

characteristic curve

Connect Com for about

13 s to +U

, until both

LEDs flash alternately

Green LED:

Yellow LED:

flashes

on: rising,

off: falling

characteristic

curve

Switch

Teach-in / synchronization

Switch off power supply

Reset to factory setting

Switch off power supply

Connect Com to -U

Switch on power supply

Keep Com connected to

-U

for about 3 s, until

both LEDs flash

simultaneously

Green LED:

Yellow LED:

flashes

on: Teach-in

off: synchro-

nization

Connect Com to -U

Switch on power supply

Keep Com connected to

-U

for about 13 s, until

both LEDs stop

flashing

Disconnect Com from -U

before switching off

power supply

Connect Com for about

1 s to +U

Normal operating mode

To change output

characteristic connect

Com for about 1 s to +U

Wait for about 10 s

To change operation mode

connect

Com for about 1 s to -U

Wait for about 10 s

Normal operating mode

 Connection, installation and

adjustment works should be car-

ried out by expert personnel only.

 No safety component in

accordance with the EU Machine

Directive

Proper use

pico+ultrasonic sensors are used for

non-contact detection of objects.

Installation

 Mount the sensor at the installa-

tion site.

 Connect a connection cable to the

M12 device plug.

Start-Up

 Connect the power supply.

 Carry out the sensor adjustment in

accordance with the diagram.

Fig. 1: Pin assignment with view onto sensor

plug and colour coding of the

microsonic connection cable

Factory Setting

 Rising analogue characteristic

curve between the blind zone and

the operating range

 Multifunctional input »Com« set

to »Teach-in«

colour

-U

brown

blue

I|U

black

white

Com grey

Synchronization

If the assembly distance falls below

the values shown in Fig. 2, the inter-

nal synchronization should be used.

For this purpose set the switched

outputs of all sensors in accordance

to the diagram »Sensor adjustment

with Teach-in procedure« at first.

Then set the multifunctional output

»Com« to »synchronization« (see

»Further settings«). Finally connect

pin 5 of the sensors plug of all sen-

sors.

Fig.2: Assembly distances, indicating syn-

chronization

Maintenance

microsonic sensors are maintenance-

free. In case of excess caked-on dirt

we recommend to clean the white

sensor surface.

Notes

 The sensors of the pico+ family

have a blind zone. Within this

zone a distance measurement is

not possible.

 The pico+ sensors are equipped

with an internal temperature com-

pensation. Due to the sensors self

heating, the temperature compen-

sation reaches its optimum work-

ing-point after approx. 20 minutes

of operation.

 In the normal operating mode, an il-

luminated yellow LED signals the ob-

ject is within the adjusted window

limits.

 If synchronization is activated the

Teach-in is disabled (see »Further

settings«).

 The sensor can be reset to its fac-

tory setting (see »Further set-

tings«).

 Optionally all Teach-in and addi-

tional sensor parameter settings

can be made using the LinkCon-

trol adapter (optional accessory)

and the LinkControl software for

windows

≥0,25 m

≥0.35 m

≥1,30 m

≥2.50 m

≥0.40 m

≥0.70 m

≥2.50 m

≥4.00 m

Ultrasonic Sensors

Set analogue output

Further settings

2004/108/EC

1 2

Podsumowanie treści

Strona 1 - Ultrasonic Sensors

Operating Instructionspico+15/I pico+15/WK/Ipico+25/I pico+25/WK/Ipico+35/I pico+35/WK/Ipico+100/I pico+100/WK/Ipico+15/U pico+15/WK/Upico+25/U pico+2

Strona 2 - Round bar ø 10 mm

Technical datablind zoneoperating rangemaximum rangeangle of beam spread20 mm150 mm30 mm250 mm250 mmSee detection zone350 mmSee detection zonetransduc

Powiązane modele: pico+15/WK/I | pico+25/I | pico+25/WK/I | pico+35/I | pico+35/WK/I | pico+100/I | pico+100/WK/I | pico+15/U | pico+15/WK/U | pico+25/U | pico+25/WK/U | pico+35/U | pico+35/WK/U | pico+100/U | pico+100/WK/U |

Komentarze do niniejszej Instrukcji

Brak uwag

Microsonic pico+15/I Instrukcja Użytkownika

Przeglądaj online lub pobierz Instrukcja Użytkownika dla Czujniki Microsonic pico+15/I. Microsonic pico+15/I User Manual Instrukcja obsługi

Podsumowanie treści

Powiązane modele: pico+15/WK/I | pico+25/I | pico+25/WK/I | pico+35/I | pico+35/WK/I | pico+100/I | pico+100/WK/I | pico+15/U | pico+15/WK/U | pico+25/U | pico+25/WK/U | pico+35/U | pico+35/WK/U | pico+100/U | pico+100/WK/U |

Komentarze do niniejszej Instrukcji

Powiązane produkty i podręczniki dla Czujniki Microsonic pico+15/I